★ Top 5 Editorial Picks — Deep Drop Fishing
- Humminbird APEX 19 MEGA SI+ ChartplotterBest Overall Depth — 2,500 ft on 2D sonar
- Humminbird HELIX 9 MEGA SI+ G4NBest for Deep Drop — 3,500 ft on optional 50 kHz
- Humminbird XPLORE 9Best Fish Finder for Deep Drop — 2,000 ft
- Lowrance HDS PRO 10Best Lowrance Fish Finder — 3,000 ft
- Garmin ECHOMAP Ultra 2 106svBest Garmin Value Pick — 1,800 ft
Humminbird SOLIX 10 CHIRP MEGA SI+ G3 Review: 1,200 ft of Stated Sonar Depth With Touch Control
DeepDropFishing.com is reader-supported. When you buy through links on our site, we may earn a commission at no extra cost to you. This review is based on the manufacturer’s published specifications.

Quick Answer
The Humminbird SOLIX 10 CHIRP MEGA SI+ G3 is a 10.1-inch touchscreen fish finder/chartplotter with Dual Spectrum CHIRP sonar, MEGA Side Imaging+ and MEGA Down Imaging+, built-in GPS and Humminbird Basemap, and full One-Boat Network networking. The number that matters for our readers: Humminbird states its Depth-Sonar at 1,200 ft (standard transducer) and 3,500 ft (optional Airmar CHIRP). That standard figure puts it in genuine deep-drop territory on paper — with the honest caveat that the MEGA imaging sonar is a shallow-water tool, rated by Humminbird to 200 ft (MEGA) down and 400 ft (MEGA) side-to-side. G3 is the latest SOLIX generation and runs Humminbird’s current 7.400 software. One honest flag for buyers: Humminbird’s US online shop no longer lists the SOLIX line for sale (checked November 2026), and Humminbird’s newest fish finder line is now XPLORE.
No Check Price button on this page: we are not linking this model’s current Amazon US offers — the featured seller’s record is too poor to send readers to (checked November 2026). If that changes, this page gets its button.
Who the SOLIX 10 Is For
The SOLIX 10 G3 is for anglers who want a big, touch-driven Humminbird at the centre of a networked boat: trolling motor, shallow-water anchors, radar and a second display all talking to one unit. Humminbird describes the SOLIX G3 Series as running on a dual-core processor with an intuitive, customisable interface, and its compatibility list is the longest in the range below APEX — MEGA Live, MEGA 360, Radar, AIS, AutoPilot and the full Minn Kota family.
For deep-drop and offshore readers, the appeal is the same one that put the HELIX 9 on this site — a manufacturer-stated 1,200 ft of 2D sonar depth from the transducer in the box — plus a touchscreen, a 10.1-inch 1280 x 800 display and an optional Airmar CHIRP path that Humminbird rates to 3,500 ft. It features in our Best Fish Finder for Deep Drop Fishing guide. If you are building a new Humminbird helm from scratch, also read our Humminbird XPLORE 9 review — XPLORE is the series Humminbird itself calls its newest fish finders, while SOLIX G3 remains a supported model one step behind it in the line-up.
Key Specs
| Spec | Humminbird SOLIX 10 CHIRP MEGA SI+ G3 |
|---|---|
| Model / Product Code | SOLIX 10 CHIRP MEGA SI+ G3 / 411530-1 |
| Display | 10.1 in Color TFT, 1280H x 800V, 16-Bit |
| Controls | Touch Screen (Cross Touch interface) |
| Sonar — standard | Dual Spectrum CHIRP, MEGA Side Imaging+, MEGA Down Imaging+ |
| CHIRP frequencies supported | Full Mode (150-220 kHz), Narrow Mode (180-240 kHz), Wide Mode (140-200 kHz), Optional Deepwater (28-250 kHz) |
| Imaging frequencies supported | MEGA SI+ (1050-1175 kHz), MEGA DI+ (1100-1200 kHz), 455 kHz SI+ (405-505 kHz), 455 kHz DI+ (420-520 kHz), 800 kHz SI+ (780-840 kHz), 800 kHz DI+ (800-860 kHz) |
| Max depth — sonar (manufacturer stated) | 1,200 ft (standard transducer); 3,500 ft (optional Airmar CHIRP) |
| Max depth — Down Imaging | 400 ft (455 kHz), 200 ft (MEGA), 125 ft (800 kHz) |
| Range — Side Imaging (side-to-side) | 800 ft (455 kHz), 400 ft (MEGA), 250 ft (800 kHz) |
| Target separation | 2.5 in |
| Power output | 1000 Watts RMS / 8000 Watts Peak-to-Peak |
| Transducer included | XM 14 HW MSI T, transom mount (not included on CHO version, 411530-1CHO) |
| GPS / charts | Internal GPS; Humminbird Basemap included; LakeMaster, CoastMaster, Navionics Gold/HotMaps and Navionics Platinum+ compatible; AutoChart Live |
| Storage | 10,000 waypoints, 50 routes, 50 tracks / 20,000 points |
| Card slots | Dual Micro SD |
| Networking | One-Boat Network, NMEA 2000, Bluetooth, Wi-Fi, Ethernet via 5-Port Ethernet Switch compatibility; MEGA Live and MEGA 360 compatible |
| Power | 10.8-20 VDC input; 2.5 Amps draw; 5A fuse (SOLIX 10 Series) |
| Mounting | Gimbal (standard), 11.81 in W x 7.89 in H x 4.78 in D; In-Dash Mounting Kit (optional) |
| Warranty | Two-Year Warranty |
Cross Touch Display and Control
The SOLIX line’s defining feature is its interface. Humminbird lists the SOLIX 10 G3’s interface simply as Touch Screen, and names the system Cross Touch: you can run the unit from the touchscreen or from the keypad, with the sidebar menu putting your most-used views a tap away and custom views letting you combine sonar, chart and instruments on one screen. That is a genuine offshore consideration — touch is fast at the dock and in calm water, and having the physical controls as a full alternative matters when the screen is wet.
The screen itself is a 10.1-inch Color TFT at 1280H x 800V — the same HD resolution class Humminbird uses across its 10-inch units — driven, per Humminbird, by a dual-core processor. Software is upgradable, and the SOLIX G3 family is on Humminbird’s current software version 7.400 (released October 6, 2026), which is also what keeps the unit network-compatible with XPLORE and APEX models and compatible with MEGA Live 2. Compare that with the keypad-only control in our Humminbird HELIX 9 MEGA SI+ G4N review: same imaging family, very different way of driving it.
MEGA Imaging Sonar: Brilliant, and Honestly Shallow
The standard sonar package is three layers deep. MEGA Side Imaging+ and MEGA Down Imaging+ run at three frequency bands each — 455 kHz, 800 kHz and the megahertz MEGA band (MEGA SI+ at 1050-1175 kHz, MEGA DI+ at 1100-1200 kHz) — and they produce the sharp, photographic structure pictures Humminbird is known for. Humminbird’s stated ranges are 800 ft (455 kHz), 400 ft (MEGA) and 250 ft (800 kHz) side-to-side for Side Imaging, and 400 ft (455 kHz), 200 ft (MEGA) and 125 ft (800 kHz) of depth for Down Imaging.

Read those numbers the right way round: the clearest MEGA pictures live in the top 200 ft, and no imaging frequency on this unit reaches deep-drop bottom. That is not a flaw — it is what imaging sonar is for. You use it to pick apart wrecks, reef edges and bait on the run out and over shallow structure, then you fish deep on the 2D view below.
Dual Spectrum CHIRP: The Deep-Water Workhorse
Underneath the imaging sits Dual Spectrum CHIRP, the traditional 2D sonar, and it is the part of this unit a deep-drop angler actually fishes with. Humminbird lists its CHIRP modes as Full Mode (150-220 kHz), Narrow Mode (180-240 kHz) for detail, Wide Mode (140-200 kHz) for coverage, and an Optional Deepwater mode spanning 28-250 kHz. Target separation is stated at 2.5 in, sonar coverage runs to 20°, 42°, 60°, (2) 86° & (2) 55° @ -10dB, and output is rated at 1000 Watts RMS (8000 Watts Peak-to-Peak).
All of it runs through the included XM 14 HW MSI T transom-mount transducer. Humminbird also lists optional sonar support for 50/83/200 kHz and Airmar High, High Wide, Medium, Medium Wide, and Low transducers — that Airmar path is where the deep numbers below come from. If you are choosing between transom, thru-hull and Airmar options, our Best Transducer for Deep Drop Fishing guide walks through the trade-offs.

Charts, AutoChart Live and the One-Boat Network
Mapping starts with an internal GPS receiver and the built-in Humminbird Basemap, with compatibility for LakeMaster, CoastMaster, Navionics Gold/HotMaps and Navionics Platinum+ charts. AutoChart Live is built in: it maps depth contours, bottom hardness and vegetation in real time as you drive, with eight hours of built-in recording time and AutoChart Zero Line SD cards for more — genuinely useful for building your own picture of an uncharted ledge before you drop on it. The unit stores 10,000 waypoints, 50 routes and 50 tracks / 20,000 points, and carries Dual Micro SD card slots.
Networking is where SOLIX earns its keep. The official compatibility list names One-Boat Network, NMEA 2000, MEGA Live, MEGA 360, Radar, AIS and AutoPilot, plus the Minn Kota family — i-Pilot Link, Talon/Raptor shallow-water anchors, US2 Sonar and Built-In MEGA DI / MEGA SI motors — with Bluetooth, Wi-Fi and 5-Port Ethernet Switch compatibility on top. One software note worth knowing: Humminbird states XPLORE units network only with XPLORE, APEX and SOLIX G3 models running software 5.060 or later, so keep a SOLIX G3 updated if you plan to mix generations at the helm. Our Deep Drop Fishing Electronics Setup guide shows how a networked display like this fits into a complete offshore system, and a simpler non-networked alternative is covered in our Garmin ECHOMAP UHD2 73sv review.
Deep-Water and Deep-Drop Use: The Verdict on Humminbird’s Own Numbers
Everything in this section rests only on what Humminbird publishes for this model. On its official product page, Humminbird states the SOLIX 10 CHIRP MEGA SI+ G3’s depth capability exactly as: Depth-Sonar — 3,500 ft (optional Airmar CHIRP), 1,200 ft (standard transducer).
That 1,200 ft standard figure is the headline. It covers the heart of the deep-drop fishery — golden tilefish, snowy grouper, queen snapper and daytime swordfish bottom work in roughly the 600–1,200 ft band — from the XM 14 HW MSI T transducer in the box, and the optional Airmar CHIRP path extends Humminbird’s stated ceiling to 3,500 ft, well past any realistic bottom-fishing depth. Note the wording carefully: the SOLIX 10’s 3,500 ft figure is tied to an optional Airmar CHIRP transducer. Do not confuse it with the HELIX 9’s 3,500 ft figure, which Humminbird ties to an optional 50 kHz transducer — same headline number, different hardware path.
Two honest limits. First, the imaging sonar is not part of the deep story: Down Imaging tops out at 400 ft (455 kHz) and 200 ft at MEGA frequencies, so below that you are fishing the Dual Spectrum CHIRP 2D view only. Second, these are the manufacturer’s stated capabilities; real-world bottom-holding at 1,000 ft and beyond still depends on transducer installation, sea state and settings, and Humminbird publishes no separate saltwater depth figure for this model.
If deep dropping is the whole mission and you are buying new today, weigh this unit against Humminbird’s newest line before deciding: our Humminbird XPLORE 9 review covers the series Humminbird calls its newest fish finders. The SOLIX 10 G3’s counter-argument is a bigger screen, the same 1,200 ft stated standard depth class, and a mature, fully supported network platform.
What’s in the Box / What You Still Need
For the standard model (411530-1): the SOLIX 10 control head, screen cover, the XM 14 HW MSI T transom-mount transducer, mounting hardware, power cable and gimbal mounting bracket. One caution: Humminbird also sells a CHO (Control Head Only) version of this exact model, product code 411530-1CHO, with no transducer in the box — it is meant for Minn Kota Built-In MEGA Imaging motors, MEGA 360 installations or networked sonar sharing. The two look identical in listings, so check the product code before ordering.
Beyond the box, budget for:
- An optional Airmar CHIRP transducer if you want Humminbird’s stated 3,500 ft sonar ceiling — the standard transducer’s stated figure is 1,200 ft.
- A premium chart card (LakeMaster, CoastMaster or Navionics) if you want more detail than the built-in Humminbird Basemap, and an AutoChart Zero Line SD card if you will map with AutoChart Live beyond its eight built-in hours.
- An In-Dash Mounting Kit if you prefer a flush helm to the standard gimbal mount.
- A fused 12 V supply run — Humminbird specifies a 5A fuse for the SOLIX 10 Series, with a 2.5 Amps power draw on a 10.8-20 VDC input.
- Networking cables / a 5-Port Ethernet Switch if you are building out a multi-unit One-Boat Network system.
Who Should Buy / Who Should Skip
Buy the SOLIX 10 G3 if you want one touchscreen unit that images the shallows in MEGA detail and still carries a manufacturer-stated 1,200 ft of 2D sonar depth for deep-drop bottom fishing; if you are already in — or building into — the Humminbird / Minn Kota One-Boat Network world (i-Pilot Link, Talon/Raptor, Cannon downriggers, MEGA Live and MEGA 360 all integrate); or if you want the Airmar CHIRP upgrade path to Humminbird’s stated 3,500 ft.
Skip the SOLIX 10 G3 if you want Humminbird’s newest platform — look at the XPLORE series first; if your fishing never passes 200 ft, where smaller and simpler imaging units cover the same MEGA picture; or if you are looking at the CHO version without already owning a compatible transducer, a Built-In MEGA Imaging trolling motor, or a networked Humminbird to supply sonar — the CHO box contains no transducer at all.
FAQ
How deep can the Humminbird SOLIX 10 G3 read?
Humminbird states Depth-Sonar of 1,200 ft (standard transducer) and 3,500 ft (optional Airmar CHIRP) for the SOLIX 10 CHIRP MEGA SI+ G3. The imaging sonar is much shallower: Down Imaging reaches 400 ft at 455 kHz and 200 ft at MEGA frequencies.
What transducer comes with the SOLIX 10 G3?
The standard model (411530-1) includes the XM 14 HW MSI T transom-mount transducer, covering Dual Spectrum CHIRP, MEGA Down Imaging+ and MEGA Side Imaging+. The CHO version (411530-1CHO) includes no transducer.
Is the SOLIX 10 G3 a touchscreen?
Yes. Humminbird lists its interface as Touch Screen — its Cross Touch system, which also allows keypad control — on a 10.1 in display at 1280H x 800V.
Is SOLIX G3 the current SOLIX generation?
Yes — G3 is the latest SOLIX generation and runs the current software version 7.400 (October 2026). Humminbird does not mark it discontinued, but its US online shop no longer lists SOLIX units for sale (checked November 2026); Humminbird’s newest fish finder series overall is XPLORE.
Does the SOLIX 10 G3 work with MEGA Live and MEGA 360?
Yes. Humminbird lists MEGA Live Compatibility: Yes and 360 Imaging Compatibility: Yes for this model, and Humminbird Help confirms MEGA Live 2 compatibility for SOLIX G3 units running software 5.060 or higher.
Can the SOLIX 10 G3 network with XPLORE or APEX units?
Yes, with a condition: Humminbird states XPLORE models are network-compatible only with other XPLORE, APEX, and SOLIX G3 models running software version 5.060 or later — so the SOLIX G3 needs to be kept on current software.
Is the SOLIX 10 G3 enough for deep drop fishing?
On Humminbird’s published figures, yes for the core of the fishery: its stated 1,200 ft standard-transducer depth covers the roughly 600–1,200 ft band where most deep-drop species are worked, and the optional Airmar CHIRP path is stated to 3,500 ft. Below about 400 ft you are fishing on 2D sonar only — the MEGA imaging does not reach deep-drop depths.
The Bottom Line
The SOLIX 10 CHIRP MEGA SI+ G3 earns its place on a deep-drop site the same way its HELIX sibling does — with one honest number: 1,200 ft of manufacturer-stated 2D sonar depth from the transducer in the box, extendable to a stated 3,500 ft with an optional Airmar CHIRP transducer. Around that number you get a 10.1-inch Cross Touch display, the full MEGA Imaging+ package for the shallows, AutoChart Live mapping and the deepest One-Boat Network compatibility list in its class. It is no longer Humminbird’s newest line — that is XPLORE — but as a supported, deep-capable touchscreen unit, it remains a strong single-display choice for smaller offshore boats.
